Anthem Integrated 225 Preamplifier in black or silver

FEATURES

A whopping 225 watts per channel of power output at 8 ohms.
Balance control, tone controls with a tone bypass switch, and a mute switch.
Analog inputs: five single-ended (RCA jack) stereo analog inputs, one balanced (XLR) stereo analog input, and a front panel mounted portable audio (mini-jack) input.
Built-in phonostage suitable for use with moving magnet or high-output moving coil cartridges. (But note: the Integrated 225 phonotion offers relatively low gain-just 35dB-so that you'll want to use cartridges with fairly high output).
Built-in headphone amp.
Superb, illuminated remote control.
Premium quality parts used throughout the audio signal path, including gold plated RCA input jacks, oversized speaker binding posts, close tolerance metal film resistors and "high-quality film signal capacitors."
Power supply that incorporates a massive "advanced generation toroidal transformer," a pair of "oversized, low-ESL, low ESR Nichicon filter capacitors," and a preamp supply "fed by two precision voltage regulators."
Fully symmetrical complementary Class AB output stage featuring "three pairs of high quality bipolar output devices per channel."

PHONO PREAMPLIFIER

Input Resistance: 47 kOhm
Input Capacitance: 100 pF
Maximum Input: 18 mV at 20 Hz, 140 mV at 1 kHz, 160 mV at 20 kHz
Gain (at 1 kHz): 35 dB
Crosstalk (at 1 kHz): 80 dB
RIAA Response: ± 0.5 dB (100 Hz to 20 kHz), -1 dB (20 kHz)
THD+N: (at 1 kHz, 5 mV input)0.05%
S/N Ratio (ref5 mV at 1 kHz, IEC-A filter): 83 dB
The phono preamplifier is suitable for moving magnet and high-output moving coil cartridges.

PREAMPLIFIER

Input Resistance: 30 kOhm
Output Resistance: 560 Ohm (Pre Out), 100 O (Rec Out)
Rated Input: 1.0 Vrms
Maximum Input: 7.6 Vrms
Minimum Load: 5 kOhm
Rated Output: (100 kO load) 1.0 Vrms
Maximum Output: 7.6 Vrms
Headphone Output: 500mWinto 32O at 0.03% THD+N
Crosstalk (at 1 kHz): 75 dB between channels, 72 dB between inputs
XLR Pin Configuration: Pin 1: Ground, Pin 2: Positive, Pin 3: Negative
Frequency Response and Bandwidth: 20 Hz to 20 kHz (+0, -0.1 dB), 1 Hz to 170 kHz (+0, -3 dB)
THD+N (at Rated Input & Output): 0.003% (80 kHz BW)
IMD (CCIF at 15 kHz & 16 kHz): 0.0005%
S/N Ratio (ref2.0 Vrms, IEC-A filter): 102 dB

POWER AMPLIFIER

Power Output (per channel, continuous RMS, 20 Hz to 20 kHz, <1% THD) 8 O: 240Wone channel driven, 225Wboth channels driven (FTC)
Power Output (per channel, continuous RMS, 20 Hz to 20 kHz, <1% THD) 4 O: 330Wone channel driven, 310Wboth channels driven (short term)
Frequency Response: 20 Hz to 20 kHz (+0, -015 dB)
Bandwidth: 1 Hz to 200 kHz (+0, -3 dB)
THD+N: 001% at 1 kHz, 003% at 20 kHz (100Winto 8O)
Power Bandwidth: <10 Hz to 100 kHz (+0, -3 dB, 200Winto 8 O)
Slew Rate: 5 V/microsecond
Headroom: 14 dB (8 O), 28 dB (4 O)
Damping Factor: 80 at 1 kHz (ref 8O)
S/N Ratio (ref 225 W, IEC-A filter): 105 dB
Crosstalk: >57 dB (100 Hz to 10 kHz)
Voltage Gain: 29 dB

CONTROL

POWER REQUIREMENT

Consumption: 300Wtypical, 800Wmaximum (8O load)
Low voltage version: In countries where the line voltage is 120V, this product operates from a single phase AC power source that supplies between 108V and 132V at a frequency of 60 Hz
High voltage version: In countries where the line voltage is 220, 230, or 240V, this product operates from a single phase AC power source that supplies between 216V and 264V at a frequency of 50 or 60 Hz

DIMENSIONS

We sell brand new, factory sealed Anthem Integrated 225 preamplifiers with full FACTORY WARRANTY.

We also occasionally have PRE-OWNED specials.